Articles
How To Reset Furnace In 5 Steps (Safe Step-By-Step Guide)
How to reset furnace equipment safely comes down to five careful steps: cycling the thermostat, the furnace power switch, and the circuit breaker, then using the reset button and clearing any lockout. A reset can bring a furnace back to life after a minor fault trips its safety controls, and it is often the first thing to try before calling for service. The key word is safely, since a furnace involves both gas and electricity. This guide walks through how to reset your furnace step by step in your Brooklyn Park home, and when a reset is not the answer.
- Reset the right way: Follow the safe sequence in order.
- Use each control: The thermostat, switch, breaker, and reset button.
- Know the limits: Understand when a reset will not fix the problem.

Before You Reset: A Quick Safety Note
Resetting a furnace is usually safe when done correctly, but because the system runs on gas and electricity, a few precautions matter before you begin. A reset clears a temporary fault, but it is not a fix for a furnace that keeps shutting down.
When a Reset Helps and When It Doesn’t
A furnace reset is meant to clear a one-time fault, so it helps when a brief interruption has tripped a safety control, but not when a real problem keeps recurring. If a power flicker, a brief lockout, or a minor glitch has stopped the furnace, a reset often restores normal operation. However, if the furnace shuts down again right after you reset it, that repetition is a signal of an underlying issue rather than a fluke. The Consumer Product Safety Commission advises that when a breaker trips, you should investigate the cause rather than simply resetting it, because a repeated trip is often a warning that something is wrong. Reset once, but do not force it repeatedly.
- A reset helps: When a one-time fault or power blip stopped the furnace.
- A reset won’t help: When the furnace shuts down again right away.
- Reset once: Repeated tripping signals a real problem to investigate.
5 Steps To Reset a Furnace
Work through these steps in order, giving the system a moment to respond at each stage. Stop and call a professional if the furnace will not stay running after a single reset.
1. Turn the Thermostat Off
Start the reset by setting your thermostat to off so the furnace is not being told to run while you work. Switch the thermostat from heat to the off position, which stops it from calling for heat and lets the system power down cleanly before you cycle the other controls. This simple first step prevents the furnace from trying to fire while you reset it and is the foundation of a safe, orderly reset. Leave it off until you have completed the steps below and are ready to test.
- Switch to off: Move the thermostat from heat to off.
- Stop the call for heat: This lets the system power down cleanly.
- Leave it off: Keep it off until you are ready to test.
2. Turn Off the Furnace Power Switch
Locate the furnace power switch, which looks like an ordinary light switch mounted on or near the furnace, and turn it off. This switch cuts power directly to the furnace, and flipping it off is a key part of a proper reset. Wait about thirty seconds to a minute with the switch off, which gives the control board time to fully power down and clear a temporary fault. Then flip it back on. In many cases, this power cycle alone resets the furnace and clears a minor lockout.
- Find the switch: It resembles a light switch by the furnace.
- Wait a minute: Let the control board fully power down.
- Switch it back on: This power cycle often clears a minor fault.
3. Reset the Circuit Breaker
If cycling the power switch does not work, the next step is to reset the furnace’s circuit breaker at your electrical panel. Find the breaker labeled for the furnace and check whether it has moved to the middle or off position, which indicates it has tripped. To reset it, push the handle fully to off and then firmly back to on. Give the furnace a minute to respond. Reset the breaker only once, because a breaker that trips again immediately points to an electrical fault that needs a professional rather than another reset.
- Check the panel: Look for a furnace breaker in the tripped position.
- Fully off, then on: Push the handle all the way off, then on.
- Only once: A breaker that retrips needs professional attention.

4. Press the Furnace Reset Button
Some furnaces have a dedicated reset button, often a red or yellow button on the blower motor housing, that you can press to clear a fault. If your furnace has one, press it once firmly after cycling the power, and wait to see if the furnace starts its ignition sequence. Not all modern furnaces include a manual reset button, so do not worry if you cannot find one, since the power and breaker cycling in the earlier steps accomplishes the same reset. If you do have one, press it a single time rather than repeatedly.
- Look for the button: Often red or yellow on the blower motor.
- Press once: A single firm press clears the fault.
- Not always present: Many newer furnaces have no manual button.
5. Restore Power and Clear the Lockout
Finally, turn everything back on in order and give the furnace time to clear its lockout and restart. With the breaker and power switch back on, set the thermostat to heat and a few degrees above room temperature, then wait, since many furnaces have a built-in delay of several minutes before the burners fire after a reset. This waiting period lets the control board clear its lockout and run through a safe startup sequence. If the furnace fires and stays running, the reset worked. If it locks out again, it is time to call a professional.
- Turn it all back on: Restore the breaker, switch, and thermostat.
- Be patient: A built-in delay can last several minutes.
- Watch the result: Staying lit means success; another lockout means call.
Frequently Asked Questions
Homeowners learning how to reset a furnace ask these most often. Short answers follow.
Where is the reset button on a furnace?
If your furnace has a manual reset button, it is usually a red or yellow button located on the side of the blower motor inside the furnace cabinet. Many modern furnaces do not have one and are reset by cycling the power switch and breaker instead. Check your owner’s manual if you are unsure.
How many times can I reset my furnace?
Reset your furnace only once. If it fires up and then shuts down again, or will not restart, do not keep resetting it, since repeated resets can mask or worsen an underlying problem. A furnace that will not stay running after one reset needs professional diagnosis.
Why does my furnace keep locking out after I reset it?
A furnace that repeatedly locks out after a reset is signaling a real fault rather than a one-time glitch, such as an ignition, flame sensor, or safety control issue. Continuing to reset it will not solve the cause. This pattern means it is time to call a technician.
Is it safe to reset my furnace myself?
Yes, cycling the thermostat, power switch, and breaker, and pressing a reset button once, are all safe for a homeowner to do. What is not safe is repeatedly forcing a reset on a furnace or breaker that keeps tripping. When in doubt, or if the problem repeats, call a professional.

When a Reset Isn’t Enough, We’re Here to Help
A furnace reset is a quick, safe first move, and when it works, it can save you a service call and get your heat back in minutes. But a furnace that will not stay running after a single, proper reset is telling you something more is going on, and that is the moment to bring in a professional rather than keep forcing it. Hoffman Cooling & Heating has kept Minnesota homes warm for 75 years from Brooklyn Park and across the Twin Cities. Our technicians find out why your furnace is tripping and fix the real cause, in plain language with no jargon and no pressure. When a reset does not do it, reach out to Hoffman and we will get your heat running reliably again.